* Add instructions on flashing ARM keyboards with default STM32 bootloader * fixed typo; added note suggestion to step 4
6.9 KiB
Flashing Instructions and Bootloader Information
There are quite a few different types of bootloaders that keyboards use, and just about all of the use a different flashing method. Luckily, projects like the QMK Toolbox aim to be compatible with all the different types without having to think about it much, but this article will describe the different types of bootloaders, and available methods for flashing them.
If you have a bootloader selected with the BOOTLOADER
variable in your rules.mk
, QMK will automatically calculate if your .hex file is the right size to be flashed to the device, and output the total size in bytes (along with the max). To run this process manually, compile with the target check-size
, eg make planck/rev4:default:check-size
.
DFU
Atmel's DFU bootloader comes on all atmega32u4 chips by default, and is used by many keyboards that have their own ICs on their PCBs (Older OLKB boards, Clueboards). Some keyboards may also use LUFA's DFU bootloader (or QMK's fork) (Newer OLKB boards) that adds in additional features specific to that hardware.
To ensure compatibility with the DFU bootloader, make sure this block is present your rules.mk
(optionally with lufa-dfu
or qmk-dfu
instead):
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel-dfu
Compatible flashers:
- QMK Toolbox (recommended GUI)
- dfu-programmer /
:dfu
in QMK (recommended command line) - Atmel's Flip (not recommended)
Flashing sequence:
- Press the
RESET
keycode, or tap the RESET button (or short RST to GND). - Wait for the OS to detect the device
- Erase the memory (may be done automatically)
- Flash a .hex file
- Reset the device into application mode (may be done automatically)
or:
make <keyboard>:<keymap>:dfu
QMK DFU
QMK has a fork of the LUFA DFU bootloader that allows for a simple matrix scan for exiting the bootloader and returning to the application, as well as flashing an LED/making a ticking noise with a speaker when things are happening. To enable these features, use this block in your config.h
(The key that exits the bootloader needs to be hooked-up to the INPUT and OUTPUT defined here):
#define QMK_ESC_OUTPUT F1 // usually COL
#define QMK_ESC_INPUT D5 // usually ROW
#define QMK_LED E6
#define QMK_SPEAKER C6
The Manufacturer and Product names are automatically pulled from your config.h
, and "Bootloader" is added to the product.
To generate this bootloader, use the bootloader
target, eg make planck/rev4:default:bootloader
.
To generate a production-ready .hex file (containing the application and the bootloader), use the production
target, eg make planck/rev4:default:production
.
Caterina
Arduino boards and their clones use the Caterina bootloader (any keyboard built with a Pro Micro, or clone), and uses the avr109 protocol to communicate through virtual serial. Bootloaders like A-Star are based on Caterina.
To ensure compatibility with the Caterina bootloader, make sure this block is present your rules.mk
:
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina
Compatible flashers:
- QMK Toolbox (recommended GUI)
- avrdude with avr109 /
:avrdude
(recommended command line) - AVRDUDESS
Flashing sequence:
- Press the
RESET
keycode, or short RST to GND quickly (you only have 7 seconds to flash once it enters) - Wait for the OS to detect the device
- Flash a .hex file
- Wait for the device to reset automatically
or
make <keyboard>:<keymap>:avrdude
or if you want to flash multiple boards, use the following command
make <keyboard>:<keymap>:avrdude-loop
When you're done flashing boards, you'll need to hit Ctrl + C or whatever the correct keystroke is for your operating system to break the loop.
Halfkay
Halfkay is a super-slim protocol developed by PJRC that uses HID, and come on all Teensys (namely the 2.0).
To ensure compatibility with the Halfkay bootloader, make sure this block is present your rules.mk
:
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = halfkay
Compatible flashers:
- QMK Toolbox (recommended GUI)
- Teensy Loader
- Teensy Loader Command Line (recommended command line)
Flashing sequence:
- Press the
RESET
keycode, or short RST to GND quickly (you only have 7 seconds to flash once it enters) - Wait for the OS to detect the device
- Flash a .hex file
- Reset the device into application mode (may be done automatically)
STM32
All STM32 chips come preloaded with a factory bootloader that cannot be modified nor deleted. Some STM32 chips have bootloaders that do not come with USB programming (e.g. STM32F103) but the process is still the same.
At the moment, no BOOTLOADER
variable is needed on rules.mk
for STM32.
Compatible flashers:
- QMK Toolbox (recommended GUI)
- dfu-util /
:dfu-util
(recommended command line)
Flashing sequence:
- Enter the bootloader using any of the following methods:
- Tap the
RESET
keycode (may not work on STM32F042 devices) - If a reset circuit is present, tap the RESET button
- Otherwise, you need to bridge BOOT0 to VCC (via BOOT0 button or bridge), short RESET to GND (via RESET button or bridge), and then let go of the BOOT0 bridge
- Tap the
- Wait for the OS to detect the device
- Flash a .bin file
- You will receive a warning about the DFU signature; Just ignore it
- Reset the device into application mode (may be done automatically)
- If you are building from command line (e.g.
make planck/rev6:default:dfu-util
), make sure that:leave
is passed to theDFU_ARGS
variable inside yourrules.mk
(e.g.DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
) so that your device resets after flashing
- If you are building from command line (e.g.