e337bb82a3
* Planck: Copy contents of Planck rules.mk to each revision * Planck: Delete Planck rules.mk * Planck: Concatenate duplicate rules Concatenate rules that are set and then overridden into one setting. * Preonic: Copy contents of Preonic rules.mk to each revision * Preonic: Delete Preonic rules.mk * Preonic: Concatenate duplicate rules Concatenate rules that are set and then overridden into one setting. * Planck: Delete non-specific Bootloader settings from revs. 1 and 2 Deleted BOOTLOADER setting code block, as the checks were only valid for revs. 3-5 and the Planck Light. Neither Planck rev1 or rev2 set the bootloader via rules.mk, so there's no setting of BOOTLOADER in their rules.mk files. * Preonic: Fix BOOTLOADER settings code blocks * Preonic: delete extra blank lines from rules.mk files * Preonic: delete AVR-type hardware config blocks from rev3 * Update Planck and Preonic readme files - update Hardware Supported - update/add Install Examples - update Docs paragraph * Enable Bootmagic Lite where it is disabled Enabled Bootmagic Lite for: - Planck Light - Planck revs. 1-5 - Preonic revs. 1 and 2 * Remove `planck_grid` from LAYOUTS rule for all Planck revisions Community has landed on `ortho_4x12`, which is already set; `planck_grid` is redundant.
68 lines
3 KiB
Makefile
68 lines
3 KiB
Makefile
# MCU name
|
|
#MCU = at90usb1287
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Bootloader
|
|
# This definition is optional, and if your keyboard supports multiple bootloaders of
|
|
# different sizes, comment this out, and the correct address will be loaded
|
|
# automatically (+60). See bootloader.mk for all options.
|
|
BOOTLOADER = qmk-dfu
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
# Build Options
|
|
# change to "no" to disable the options, or define them in the Makefile in
|
|
# the appropriate keymap folder that will get included automatically
|
|
#
|
|
BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
|
COMMAND_ENABLE = no # Commands for debug and configuration
|
|
NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
|
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
|
MIDI_ENABLE = no # MIDI controls
|
|
AUDIO_ENABLE = yes # Audio output on port C6
|
|
UNICODE_ENABLE = no # Unicode
|
|
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
|
|
RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
|
|
API_SYSEX_ENABLE = no
|
|
|
|
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
|
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
|
|
|
|
LAYOUTS = ortho_5x12
|